|
Woodmont Doors
Series 500 slab drawer fronts and F and FC 5-piece drawer fronts |
Series 500 slab drawer fronts can be used with any series of door. Matching edges are available when used in conjunction with Series 200 and 400 doors. When used with Series 100 or 300 doors, some edge
options might not be availble because there are special edge configurations on the mitered corner wood doors.
Style 500FF slab drawer front is a one-piece drawer front meant to give the impresssion of a raised panel front. The F and FC drawer fronts for Series 200 and 400 doors are 5-piece matching drawer fronts. Same for
series 100 and 300 drawer fronts. Greater minimum height requirements are needed on 5-piece drawer fronts vs. slab drawer fronts. Some of the same pictures you viewed on the door series pages will be shown below.
Pricing for drawer fronts will be found in the price grids on each door series page. Profile selections are also shown on each door page. This page is just meant to summarize all the drawer fronts on the same page.
|
Design 200 door shown with design 200F drawer front above. The 200F drawer front is 5-pieces just like the doors, all 4
frame pieces will be equal width, and the minimum height requirement is 7" tall. For shorter height raised panel drawer fronts, design 200FC, min. height requirement is 5-1/2". Top
and bottom rails will be narrower than side frame rails. For drawer fronts 3-12" tall to 5-7/16, order design 500 with the matching edge to your doors.
Shown in Cider Cherry finish.
|
Design 200 door shown with design 500FF drawer front above. The 500FF drawer front is slab drawer front, one piece.
It is meant to mimic a raised panel look and the min. height requirement is 5-1/2". For drawer fronts 3-12" tall to 5-7/16, order design 500 with the matching edge to your doors.
Shown in Autumn Oak finish.
|
Design 400 door, E frame SQ edge.
The ever popular Shaker style door.
Shown in Autumn Oak finish.
Min. width 6-1/2", min. height 6-1/2"
Design 500-SQ slab drawer front shown above door.
Min. height requirement for this style of drawer front is 3-1/2"
5-piece plywood panel drawer fronts for design 400FC shown to the right must be at least 4-1/2" tall. For design 400F drawer front where all 4 frames pieces are the same width, min. height
is 6-1/2". If you increase the frame widths as shown to the right, then the min. width requirement increases also.
Autumn Oak veneer on face frame.
|
Design 400 door, E3 frame, SQ edge.
Design 400FC S3-SQ drawer front. Notice that top and
bottom rails are narrower than left and right rails.
3" wide frame choice. Available on all series 200 and 400 door frames. Standard size is 2-1/8". Mid size is 2-3/8".
2-3/8" and 3" frames carry an upcharge.
Shown in Cider Cherry finish.
Door: Min. width 8-1/4", min. height 8-1/4" because of the 3" wide frame choice.
Drawer front: Min. width 8-1/4", min. height 4-1/2" because of
the 3" wide frame choice. (Top and bottom rails will be narrow, only left and right rails are 3".)
|
Drawer front design 500FF.
Shown in Ginger Cherry finish.
Min. width is 6", min. height is 5-1/2".
Drawer front design 500FF.
Shown in Autumn Oak finish.
Min. width is 6", min. height is 5-1/2"
Design 385F drawer front with 'B' plywood panel and PRE edge choice. Shown in Espresso Maple finish with almond glaze.
Please note, the 385F drawer front has a minimum height
requirement of 6-1/2". If you have drawer fronts less in height and would like a matching beaded panel look, order them as 385FC. The 385FC has a minimum height requirement of
5-1/2". And drawer fronts under 5-1/2" in height will need to be requested as the 500-(edge choice) slab drawer fronts.
|
Drawer front design 400FC E3-SQ
Min. width for E3 frame 8-1/4", min. height 4-1/2"
Shown in Cider Cherry finish.
Shown in Cordovan Cherry finish.
Shown in Ginger Cherry finish.
|
All doors are available in Red Oak, Maple, Cherry or Hickory woods. Paint grade available too.
Doors can be ordered unfinished, or you can request finishing from the choices below.
If you would like a glazed finish, glaze colors are chocolate, bronze, mocha, and almond.
Paint grade doors come unfinished only, they are fine sanded and ready for you to paint.
PLEASE NOTE: Finish choices are restricted by wood species.
Autumn Oak, Nutmet Oak, Harvest Oak, and Charcoal Oak are Oak wood finish options.
Harvest Maple, Natural Maple, Toffe Maple, Ginger Maple, Champagne
Maple, Cider Maple, Cordovan Maple, and Espresso Maple are Maple wood finishes.
Cider Cherry, Cordovan Cherry, Ginger Cherry, and also Natural Cherry are Cherry wood finishes.
Cider Hickory, Natural Hickory, and Autumn Hickory are Hickory wood finishes.
|
PROCEED TO:
|
PROCEED TO:
|
|
